The Magic Café
Username:
Password:
[ Lost Password ]
  [ Forgot Username ]
The Magic Cafe Forum Index » » The workshop » » Milk Pitcher (0 Likes) Printer Friendly Version

 Go to page [Previous]  1~2~3~4
Michael Baker
View Profile
Eternal Order
Near a river in the Midwest
11161 Posts

Profile of Michael Baker
Hmmm... could be a good way to take the cheap road on buying the beer.

"Aww, gee whiz guys... you drank that whole pitcher already?? I guess it's somebody else's turn to buy the next one."
~michael baker
The Magic Company
Kent Messmer
View Profile
Veteran user
Montana
337 Posts

Profile of Kent Messmer
This isn't a perfect fix but... after actually using duct tape to fix on a tour I was doing,(couldn't find clear tape to stick to the plastic and they couldn't see the duct tape anyway.) I just used the bottom of a 2 liter soda bottle. It fits inside ok but need to find one that does not have the "feet" of the bottle molded into bottom. I've seen bottles that have a plastic cap that is glued onto the bottom of the round bottom bottle.

This one works ok for stage but closer they might notice a depth difference. I get around it by not "pouring" out so much milk. this covers the inside milk.

Anyway, hope that helps.

Kent
Michael Baker
View Profile
Eternal Order
Near a river in the Midwest
11161 Posts

Profile of Michael Baker
We used to use that type of bottle and made our own pitchers at a magic shop in Birmingham, AL. We used the classic flute-sided plastic beer pitchers common at restaurant supply houses.

http://www.pubsupply.com/Pitchers/60-oun......8014.htm

A dab of aquarium silicone kept the insert in place, so it wouldn't float. I haven't seen those bottles for years though. I can only find the ones with the molded "feet". Bummer...
~michael baker
The Magic Company
kusoyon
View Profile
New user
Muskegon, Michigan
78 Posts

Profile of kusoyon
I have one for sale....contact me at kusoyon@comcast.net
Thanks,
Frank Thomas
"The closer you look; the less you see"
H. Blackston Jr.
seforeman
View Profile
New user
86 Posts

Profile of seforeman
Not sure anyone mentioned, but there is one on Ebay for sale currently for $20.00. Had one of these when I was younger - loved the classic design of it. Also in "Great Tricks of the Master Magicians" by George Gilbert and Wendy Rydell c1977 on page 66 he describes how to make the gimmick for a Milk Pitcher. However I am not sure his design was ever tested (as looking at the illustrations, the gimmick would float out).

Hope that helps.

Stuart
Stuart Foreman
DonB!
View Profile
Regular user
Minnesota
128 Posts

Profile of DonB!
If you are still looking for this milk pitcher, please contact me via email. I have 5 for sale, all used, but still in working order, for $5.00 each.

Email: donbursell (at) gmail (dot) com

Hope I can be of help.

DonB
DonB!
Non-stop laughter. Eternal Impact.
magicwatcher2005
View Profile
Elite user
Washington state
446 Posts

Profile of magicwatcher2005
I would try starting with a plastic water bottle (disposable) and with a decent screw-on lid, then fit the lid with a schrader valve. Find a flexible, but firm (not easily compressed) material like poly foam sheeting that you can cut and glue-seam together into a "liner" for the glass pitcher.

Now put the poly liner in the pitcher, heat the water bottle in boiling water (or an oven) until very soft, then insert inside the liner & pitcher. Screw the lid onto the bottle and then use a bicycle pump to inflate the water bottle, forcing it to conform to the shape of the pitcher. The poly foam liner creates a space for the liquid load and should be flexible enough to pull out (maybe in pieces) after the plastic bottle cools. Trimming off the top of the bottle using x-acto knives and/or dremel tool is where your skill as a builder might be tested the most.
David Todd
View Profile
Inner circle
1660 Posts

Profile of David Todd
I'm trying to make the feke for a pitcher , using this cone pattern generator to cut it out from a sheet of acetate:

https://www.blocklayer.com/cone-patterns.aspx

The pitcher I'll use is slightly tapered , so it is wider at the top than at the bottom , which means I entered the inside diameter of the narrow end of the pitcher and the inside diameter of the wider end of the pitcher , and entered the height of the pitcher . I adjusted the dimensions a bit to allow a little extra room for the feke to fit into the pitcher , so it doesn't fit too tight. Ideally about 3/16" amount of space. The height of the feke will not be exactly as high as the top edge of the pitcher , but will be a bit below the top edge of the pitcher. (this will vary depending on the size and shape of the pitcher used.) Entering those numbers into the cone pattern generator will get a printable pattern to use as a guide to cut out the feke from a sheet of acetate at the correct size. Then I'll use a water-proof clear-drying glue to attach a bottom disc to the lower (narrow) end of the feke, so one end of the feke is closed and the other end is open. Then I'll insert it into the pitcher , but first glue a thin rare-earth magnet to the center interior of the feke and glue another thin rare-earth magnet on the center of the bottom of the pitcher so the feke will be held securely in place by the magnets ,but it could be removed if necessary for cleaning. I'll also use a hole punch to punch out three holes near the upper front edge of the feke to allow liquid to flow through.

See an example here . If you do this, your dimensions may vary , depending on size/shape of pitcher used. NOTE: for the squarish shaped pitcher (like this one) you would need to spend more time shaping the feke to conform to the squarish inside shape of the pitcher. From what I understand this was done by using a wood block or hard-baked clay form that has the interior dimensions of the pitcher , then using a slightly heated sheet of acetate which is molded around the wood or clay form to get the squarish shaped feke ... as has been discussed earlier in this topic, using a vacuum-forming process might be a better solution.)
The Magic Cafe Forum Index » » The workshop » » Milk Pitcher (0 Likes)
 Go to page [Previous]  1~2~3~4
[ Top of Page ]
All content & postings Copyright © 2001-2020 Steve Brooks. All Rights Reserved.
This page was created in 0.14 seconds requiring 5 database queries.
The views and comments expressed on The Magic Café
are not necessarily those of The Magic Café, Steve Brooks, or Steve Brooks Magic.
> Privacy Statement <

ROTFL Billions and billions served! ROTFL