|
|
GS121002 Veteran user but he still can't help build a border wall with only 313 Posts |
I am in need of some super jumbo printable card blanks. I have found jumbo (4x6) printable card blanks but not super jumbo (8½ x 11). I also need to use roughing spray on them to make a super jumbo Invisible deck for a stage presentation. Any and all ideas welcome.
Gary Salisbury San Diego, CA
Gary Salisbury
San Diego, CA It's a fact! - Any sufficiently advanced technology is indistinguishable from magic. (This line censored by Dave Scribner because it is in Latin) - What you believe is real, is real! Who was that masked man and what is he all about? - https://www.pinterest.com/garydsalisbury/ |
Bill Hegbli Eternal Order Fort Wayne, Indiana 22797 Posts |
Lybrary.com sells card stock in large sheets. They also have instructions for printing.
|
jimgerrish Inner circle East Orange, NJ 3209 Posts |
I like using Epson Ultra Premium Glossy Photo Paper (8½ x 11)- two sheets glued back to back with a sheet of black tissue paper between them so they are completely opaque. If using roughing fluid on one side, use Matte finish paper for that side and glossy for the un-roughed side (smoothed with fanning powder). However, I would never consider making an entire Invisible Deck that size- too awkward to handle. Instead, I would give the large (ungimmicked) super jumbo deck to the spectators to shuffle/mix and then to choose three (or so) random free choice cards, while I use a 4x6 invisible jumbo deck to match their choices and as they turn their large cards around, I would turn my smaller cards to show that each one matches. Since I would be printing the cards myself, I would print the 4 x 6 cards with very large corner pips in the center of each card, as is sometimes done with regular size cards to make them easier to see for those with bad vision. In other words, the printing on the smaller deck would actually be the same size as the ultra jumbo deck without all the unnecessary pips. The cards showing in my current Avatar are almost that large size, printed as I described.
Jim Gerrish
magicnook@yahoo.com https://www.magicnook.com Home of The Wizards' Journals: https://magicnook.com/wizardsTOC.htm |
GS121002 Veteran user but he still can't help build a border wall with only 313 Posts |
Quote:
On Jan 22, 2020, jimgerrish wrote: Jim, Thanks for the reply back. I'm not going to do an entire deck, Only about 7 or 9 cards and print the faces of magicians on them. How do you glue them together? Contact photo spray? My concern is the cards won't be stiff enough. Also a concern over whether the roughing spray would interact with the ink print. What do you use for roughing spray? Didn't think about the fanning powder. Where could I get that? Where did you get the card back image in a high enough resolution for a clear 8½ x 11 print? Did you use standard card face images? Where did you get them?
Gary Salisbury
San Diego, CA It's a fact! - Any sufficiently advanced technology is indistinguishable from magic. (This line censored by Dave Scribner because it is in Latin) - What you believe is real, is real! Who was that masked man and what is he all about? - https://www.pinterest.com/garydsalisbury/ |
jimgerrish Inner circle East Orange, NJ 3209 Posts |
I use rubber cement to glue the cards together back to back, with black tissue in between. By "stiff enough" you mean "stiff enough for your use" which is probably different for everyone, so you would just have to try it to see if it meets your needs. I don't know of any "stiffness test" for cards. However, you could use a stiff black paper rather than tissue paper between the glued cards.
I use a light spray of Clear Krylon Workable Fixatif Spray for roughing fluid. Fanning Powder is Zinc Stearate chemically, available from Amazon either by that name or as "Magician's Fanning Powder." Fanning Powder is also available from most magic stores. You can scan standard card faces from jumbo cards. Scanning at 300 dpi gives you sufficiently sharp images for most sizes you can print. You are using the scanned images for your own private use so there are no copyright worries. You can also scan card backs, but I like making my own back designs for things like my Cat in the Hat Cards, for example.
Jim Gerrish
magicnook@yahoo.com https://www.magicnook.com Home of The Wizards' Journals: https://magicnook.com/wizardsTOC.htm |
GS121002 Veteran user but he still can't help build a border wall with only 313 Posts |
Quote:
On Jan 21, 2020, Bill Hegbli wrote: Is this what you were referring to? https://www.lybrary.com/search.php?keywords=blank+cards
Gary Salisbury
San Diego, CA It's a fact! - Any sufficiently advanced technology is indistinguishable from magic. (This line censored by Dave Scribner because it is in Latin) - What you believe is real, is real! Who was that masked man and what is he all about? - https://www.pinterest.com/garydsalisbury/ |
John Martin Inner circle 1017 Posts |
Would already printed cards work for your Invisible deck.
https://www.amazon.ca/Hapros-Super-Jumbo......dHJ1ZQ== John |
GS121002 Veteran user but he still can't help build a border wall with only 313 Posts |
Quote:
On Jan 23, 2020, John Martin wrote: Thanks for the reply back, John. No, preprinted cards won't work as I want to print faces of magicians on them. I was hoping to find Super Jumbos with the backs pre-printed and blank faces.
Gary Salisbury
San Diego, CA It's a fact! - Any sufficiently advanced technology is indistinguishable from magic. (This line censored by Dave Scribner because it is in Latin) - What you believe is real, is real! Who was that masked man and what is he all about? - https://www.pinterest.com/garydsalisbury/ |
DaleTrueman Veteran user Australia 317 Posts |
I have done similar to Jim Gerrish for my large three card monte
I created the card faces I needed in photoshop, then got those and some images of the card backs printed on photo paper at the shop at 21cm by 30cm and glued these to stiff cardboard front and back.. Glued around the edges for strength and then covered in a layer of polyurethane. Whether this would work for a rough smooth application I don't know but these are very durable cards. Possibly another method would be needed for what you want to do. |
jimgerrish Inner circle East Orange, NJ 3209 Posts |
Try embedded thin magnets for a rough-smooth substitute.
Jim Gerrish
magicnook@yahoo.com https://www.magicnook.com Home of The Wizards' Journals: https://magicnook.com/wizardsTOC.htm |
The Magic Cafe Forum Index » » The workshop » » PRINTABLE SUPER JUMBO CARD BLANKS (1 Likes) |
[ Top of Page ] |
All content & postings Copyright © 2001-2024 Steve Brooks. All Rights Reserved. This page was created in 0.05 seconds requiring 5 database queries. |
The views and comments expressed on The Magic Café are not necessarily those of The Magic Café, Steve Brooks, or Steve Brooks Magic. > Privacy Statement < |